description[de] = \n\n\n\n\n

\nEurocircuits-EAGLE design rules
\n
\nSetup for 6-layer PatternClass8 BaseCopperO18-I18\n

\n The option Sizes-Minimum Drill is set to 0.25mm. This minimum drill endsize can be set lower if needed. Values below 0.25mm will result in a higher DrillClassification. For details see the Eurocircuits Classification overview.\n

\nExtra Notes:
\n- The option Distance-Copper/Dimension is set to 0.25mm, the default for boards with a routed boardoutline. If you require Vcut on your board this parameter should be set to 0.45mm.
\n- The option Supply-Generate thermals for vias is on by default but may be changed if required.
\n- The option Mask-Stop is set to 0mm oversize which is the preffered value.
\n- The option Mask-Cream is set to 0mm oversize by default, but may be changed if required
\n- The option Mask-Limit is set to 0.45mm, resulting in covered or tented via holes for vias of 0.45mm and smaller. The option may be changed if required.
\n- The options Shapes and Misc are not relevant. Values for Shapes-Smds-Roundness are not critical and can be set as you require.\n

\n

\nYou can set higher minimum values if you wish, setting lower minimum values is not advisable.
\nIf you need lower minimum values, please use a different Eurocircuits-EAGLE design rule file. For details see the Eurocircuits-EAGLE dru overview table.\n

\nYour Eurocircuits Team\n description[en] = \n\n\n\n\n

\nEurocircuits-EAGLE design rules
\n
\nSetup for 6-layer PatternClass8 BaseCopperO18-I18\n

\n The option Sizes-Minimum Drill is set to 0.25mm. This minimum drill endsize can be set lower if needed. Values below 0.25mm will result in a higher DrillClassification. For details see the Eurocircuits Classification overview.\n

\nExtra Notes:
\n- The option Distance-Copper/Dimension is set to 0.25mm, the default for boards with a routed boardoutline. If you require Vcut on your board this parameter should be set to 0.45mm.
\n- The option Supply-Generate thermals for vias is on by default but may be changed if required.
\n- The option Mask-Stop is set to 0mm oversize which is the preffered value.
\n- The option Mask-Cream is set to 0mm oversize by default, but may be changed if required
\n- The option Mask-Limit is set to 0.45mm, resulting in covered or tented via holes for vias of 0.45mm and smaller. The option may be changed if required.
\n- The options Shapes and Misc are not relevant. Values for Shapes-Smds-Roundness are not critical and can be set as you require.\n

\n

\nYou can set higher minimum values if you wish, setting lower minimum values is not advisable.
\nIf you need lower minimum values, please use a different Eurocircuits-EAGLE design rule file. For details see the Eurocircuits-EAGLE dru overview table.\n

\nYour Eurocircuits Team\n layerSetup = (1+2*3+4*5+16) mtCopper = 0.018mm 0.018mm 0.018mm 0.018mm 0.018mm 0.035mm 0.035mm 0.035mm 0.035mm 0.035mm 0.035mm 0.035mm 0.035mm 0.035mm 0.035mm 0.018mm mtIsolate = 0.2mm 0.36mm 0.3mm 0.36mm 0.2mm 0.2mm 0.2mm 0.15mm 0.2mm 0.15mm 0.2mm 0.15mm 0.2mm 0.15mm 0.2mm mdWireWire = 0.125mm mdWirePad = 0.125mm mdWireVia = 0.125mm mdPadPad = 0.125mm mdPadVia = 0.125mm mdViaVia = 0.125mm mdSmdPad = 0mil mdSmdVia = 0mil mdSmdSmd = 0mil mdViaViaSameLayer = 0.2mm mnLayersViaInSmd = 2 mdCopperDimension = 0.25mm mdDrill = 0.35mm mdSmdStop = 0mil msWidth = 0.1mm msDrill = 0.25mm msMicroVia = 25mm msBlindViaRatio = 0.500000 rvPadTop = 0.250000 rvPadInner = 0.250000 rvPadBottom = 0.250000 rvViaOuter = 0.250000 rvViaInner = 0.250000 rvMicroViaOuter = 0.000000 rvMicroViaInner = 0.000000 rlMinPadTop = 0.15mm rlMaxPadTop = 2.5mm rlMinPadInner = 0.175mm rlMaxPadInner = 2.5mm rlMinPadBottom = 0.15mm rlMaxPadBottom = 2.5mm rlMinViaOuter = 0.1mm rlMaxViaOuter = 2.5mm rlMinViaInner = 0.125mm rlMaxViaInner = 2.5mm rlMinMicroViaOuter = 2.5mm rlMaxMicroViaOuter = 25mm rlMinMicroViaInner = 2.5mm rlMaxMicroViaInner = 25mm psTop = -1 psBottom = -1 psFirst = -1 psElongationLong = 100 psElongationOffset = 100 mvStopFrame = 0.000000 mvCreamFrame = 0.000000 mlMinStopFrame = 0mil mlMaxStopFrame = 0mil mlMinCreamFrame = 0mil mlMaxCreamFrame = 0mil mlViaStopLimit = 0.45mm srRoundness = 0.000000 srMinRoundness = 0mil srMaxRoundness = 0mil slThermalIsolate = 0.2mm slThermalsForVias = 1 dpMaxLengthDifference = 10mm dpGapFactor = 2.500000 checkGrid = 0 checkAngle = 0 checkFont = 1 checkRestrict = 1 useDiameter = 13 maxErrors = 50